Magnetic Vortex Generator -
This coil is the heart of configuring the device for a diamagnetic outflow or inflow
There is much leeway in the coils, they can be custom sized to fit
the device however try to keep the diameter under 1". 3/4" is optimal
and bigger is not better.
If a crystal ball will be used keep the coil
shorter then the ferrite ring so the ball will sit on top for vertical
For horizontal alignment check the inside diameter of the
Aluminum tube - 3/4" diameter cut to 1 1/2 " [or a Golden Light length
of approx 1.9" for horizontal operation]
Bismuth shot BB's [enough to fill the tube about twice there will be
24 gauge copper or tinned copper hookup wire about 20'
Electrical tape Grey or red as black is rather ugly
1 Pkg modeling clay
1 small cast iron melting pot
Cookie sheet or other small pan
1 Propane torch - [or stove top can be used burner on high 520 deg F]
1 hot pad mitten for pouring
The coil is made from an Aluminum tube 3/4" outside diameter 1 1/2"
long. It is filled with Bismuth.
Using a small pan cover the bottom
with Aluminum foil.
Set the tube upright and then seal it on the
outside with a thick ring of modeling clay to contain the bismuth from
escaping as it cools.
The Bismuth is shot BB's that can be found
at a reloading supply store. It is melted in a small cast iron melting
pan that can be found at a kitchen supply store.
It takes about 520
degrees F to melt the Bismuth, I used a propane torch. Bismuth expands
as it cools so do not fill the tube completely.
Take your time in the
melting and slowly swirl the pan to get all the shot melted.
be some scum at the top but as you pour the liquid bismuth the scum
will be the last thing out so do not worry about it.
Let the core cool
well before touching it!
The best coils will crystallize along the top
of the coil as they cool and heating the metal longer and hotter will
After cooling the Bismuth will expand out the top of the slug as much
as 1/4" or so.
If making a Golden Light fractal length slug, be sure
the entire tube is full with no air gaps below the top of the tube.
end must now be ground down on a grinder to exactly 1.8975" both ends
as perfectly flat and perpendicular as possible.
As you grind it down
when you hit 1.9" you may feel the Light resonance, or upper heart [sun
energy] pop out, this is usually far enough.
The flat ends act like
mirrors to set up an internal light bouncing system of nodes inside the
Next wind the coil:
Subtle Vibration Test
Hold the scalar bismuth coil in the
left hand. Strip about 1/4" of insulation off the wire, and touch the
two ends together.
You may be able to feel the vibrational field rise from the coil into
your hand as the two wires make contact.
Hold the ends shorted together now for a time and see if you can feel
the bismuths vibration bubble.
If you have a second bismuth core, place it in the right hand, and now
feel how the energy jumps across to it through your body.
The second core will vibrate up then also, without a winding on it yet.
You can short the ends, and then release them many times to get a sense
of how pulsing this coil will work with an F gen.
The ferrite ring can be scavenged from an older computer monitor, the
bigger the better.
It is a slow job and care must be taken not to break
the ferrite as the chalking is chipped off near the bottom.
ring sits inside the yoke on the back of the picture tube.
If you do
not know anything about TV sets and discharging the lethal voltages get
someone who knows as the voltages
present even in a powered down set
can be lethal if the bleeder resisters have gone opened and are faulty.
Be sure to keep the metal clips that hold the two halves
of the ferrite ring together.
If a ferrite ring is not available a 2
1/4" or 2 1/2" diameter iron pipe nipple can be used about 2" long,
the cost of the desired angle at the base of these ferrites.
K & J Magnetics
Many patterns can be used to set up the magnetic field however
magnets are recommended of sufficient quantities for a strong outflow
to be achieved.
Here is my latest recommendation:
24 each type DC2 3/4" x 1/8" disc [placed around the bottom
in six locations of 4 each stacked]
24 each type DA2 5/8" x 1/8" disc [Placed around the top in six
locations of 4 each stacked]
Optional magnets can be added to these of a smaller 1/2" x 1/8" size to
expand the fields width. D82 is a good choice.
If a large crystal ball is used this will expand the field envelope. A
good magnet layout may cost around $60.
Use a compass
to make sure
magnets are placed correctly.
should be out on all the magnets and no reversals should appear
anywhere along the ferrite ring.
Depending the size of the ferrite ring
it could take more or less magnet stacks.
There will be a maximum limit
of magnets before they start to push one another off.
Function generator coil:
The Red coil around the ferrite ring shown above is optional and offers
interaction with the iron atoms.
It is used to create an Electron
inflow or outflow vibration using a function generator to excite the
It is made by laying red electrical tape turned
sticky side out along the ferrite then wrapping a twin lead 24 gauge
wire around it between the magnets
as thick as desired then wrapping
the tape over to hold the shape of the ferrite so the coil can be
To configure this coil for scalar operation the wires
from each end of the coil are fed opposite directions for a magnetic
As an option one end can be shorted and taped then
the coil is fed from the other end.
The green Tesla type pancake coil has now been shown to be
effective and useful as well for an
Electron activation element in the
device if one is researching power generation effects or just wants to
feel the Electron heat energy.
It easily throws out a 6 foot field
around the unit with no bismuth coil inside just from the magnet, iron,
coil interaction so lends to creating an Electron vortex
This field is comfortable to work around and has no
ill effects I have found as with the Lakvolsky and Mobius coils
that produce chaotic energy.
The crystal, if used, may be turned so that
the lattice forms a V to the center of the unit rather then flat
because this coil produces a conical field.
About 24 feet of #12 solid copper wire
SPDT switch [optional]
8 feet hookup wire [optional]
The coil is #12 solid copper wire with insulation, two wires stacked
one on top the other.
I placed 9 turns on this coil but the winding
could extend fully to the ends of the longest magnets for the greatest
The coil is wound from the center of the wire,
If you want an
on off switch cut the two wires apart and solder them to smaller
jumpers for extending to a switch,
if not, just bend it over at
the center lay it flat on the ferrite ring and start the wrapping
Tape the next layer at each quarter turn and keep both stacked
When you get to the outer end of the coil strip 1/4 inch and
tape the ends together so they are touching, or solder to smaller wires
for on off switching.
Both ends of the coil must be switched on and off
using a DPST switch other wise either end will act to cancel magnetic
Radiation pattern is a conical shape off the precession angles of the
magnetic poles of the iron atoms and the Neo magnets and is found to be
A program is available on the Kosol Core Tech group that has been
especially designed to drive the coils using a computer sound output.
If this is used an 8 ohm to 100 ohm resister may be placed in series
with the coil to protect the sound card of the PC,
however I have never
found this to be necessary for any of my computers.
Other wise a function generator can be purchased to drive the coil.
Ideally one can experiment with frequencies,
however NMR resonance
effects happen between 1 and 20 Mhz for the metals present. Frequencies
even as low a 8 Hz have been used,
but I recommend the higher
frequencies. As one works with the frequencies they normally tend to
increase them over time.
Up around 19Mhz is much more intense, and I find 7 to 15 Mhz to be
around where the dials usually end up for me.
The crystal ball pictured is a 125 mm Diameter Calcite sphere.
Quartz crystals have a natural electric vibration and any spheres can
Since the research using the Light Rods and the earth grid, it has
been discovered that the RM units can be aligned such that they will
couple into the earth grid.
In this configuration there is a much
faster connection moving consciousness through
other points then in external sliding.
With two such systems coupled
into the earth directly both parties may establish a psi connection
between them with near instant connection speed.
It is not known why an
earth connection is faster, just noted that it is well worth the effort.
Set up the magnet count on the ring of the ferrite to a sub multiple of
24. 8 is a good number for a fit on the rings.
There are two alignments
noted that help tremendously.
If a Bismuth slug is fabricated using the
Golden light length [just at or slightly under 1.9" long,] this coil is
then placed on its side and aligned E/W if possible.
alignment will amplify the output, as well now finding a correct
Function generator frequency
set the Golden Light into a strong Radiance mode.
Now the outer ring
to fit the wheel of 24, one of the magnet sets will point roughly N/S,
and as you find the correct alignment it will be sensed as a great
expansion of the RM fields outwards as the E/W magnets couple in.
could be done with any even number of magnets that will fit the wheel
of 24, which is set on 15 degree increments of compass angles.
Further if you can locate an earth grid point in your work area setting
up exactly on this point will allow a much more perfect linking.
caution , this is an advanced technique that may require personal
healing. I do not personally believe any earth points are toxic,
some folks are simply not ready to open to a strong flow of reverse
spin, or Kundalini energy. Once contact is established through the
earths grid system,
you will likely not want to decouple, the earth
Light is strong. I look forwards to a day where there are a great many
coupled in as I scan the earth.
At present there are only a very few doing this regularly that I am
Kosol Core Tech 9 - 29 - 6
Back To Magnetism