VE and Tubes


Tubes

The following were discovered after palming tubes cut for experiment. This is not theory but appears to be how it works.
                                                                                VE

Align either a triangle or a square with opposite side on the vector equilibrium and fit the form to a tube as a polygon.
The tube will raise corresponding external vibrational node points in the air around the tubes center based on this pattern.
The two patterns are pyramids that join tips. One pyramid is a square base and one is a triangle base.
A larger tube can also fit over the Hex form outer ring. These are the 3 VE polygons that will fit a tube.

                                          VE1


3 Polygon Patterns

Perimeters will be triangle 3 to square 4, a 3 / 4 ratio for perimeter frequency phasing. Also a Hex 6 on the larger possible single ring but the length comes out the same as the triangle as seen above on the left. From this pattern raises all the quadrature vibration relationships and all the 45 degree relationships. The two systems will move through one another at 45 degrees sharing one segment length and set up the root hex form. [This 45 degree alignment is a constant in much palming work, noted to exist between EM and Torsion fields.]

The Hex pattern will pop out along 4 planes or equators, all converging on the center point harmonically also.
VE is generally associated with spheres as a platonic, however it will also fit the tubes, is the first form to pop out, and the strongest.


VE Tube Cutting Formulas:

Square Pyramid Form Mass Resonance

Tube length = Diameter                              [even count standing form]
Tube length = Radius                                  [odd count canceling form]

Tetrahedron Form Mass Resonance

Tube length = Diameter * .7071067 * 2     [even count standing form]
Tube length = Diameter * .7071067           [odd count canceling form]


Externally Generated Node Patterns

Square Pyramid will raise a larger square around the tube at center, by forming another set of pyramids on the tube rings outwards. The other half of the ones pointing inwards.

Tetrahedron Pyramid will raise a Hex pattern around the tube and on each segment triangle will rotate 30 degrees end to end of the tube.

Either form can be stacked in even or odd halves. An odd stack will set up a canceling, and an even will set up a strong pull.


Radius

Radius

The bottom diagram pinpoints the nodal points sensed. The effect is "light feeling" and pleasant.
Note the square pyramids are vibrationally entrained by the tube to all turn one direction and become coherent on a larger scale.
The tube seems to turn its radiant field inwards, and lowers gravity sensation.


Diameter

Tube length = Diameter

Diameter

Note the origin of all 90 degree quadrature alignments in this strong structure. This cut on a tube results in heavy sensation and strong gravity due to outflow increase.


Tetrahedron

Tube length = Diameter * .7071067 * 2

Tetra


Mixing Tetrahedron and Square Pyramids


3Tube
 
VE Tubes

Showing a 1 segment Tetrahedron resonant cut Aluminum tube, inside a Square pyramid resonant cut copper tube.
One can get a feel for what happens if we set up two alignments of the VE and then mix the energy on a set of nodal points.


The intention above was to set up two tubes, such that many nodes will overlap in space having opposing alignment. The center node aligns perfectly, and the outer 4 nodes of the copper also lays over the outer 6 nodes of the Aluminum. This allows tunning by turning them. You can get 2 of the nodes to fully overlap. Moving a finger in and out over the mixed nodes is like pushing through a needle, or a little point of electric vibration.

At a diameter of 1.5" the nodes all cross very close. The next tube out can now take the mixed energy and channel it into another grid of any size using perimeter coupling.
This is a little Torsion engine. You can slowly turn the inner tube and adjust for either strong output, or "null" output.

This arrangement has inflow tube inside outflow tube, and generates a vacuum layer boundary between them.


Levitation Site Index