# Frequency

[Document with respect to making coils, in attempts to replace the Joe Cell with a Scientific device that will do similiar. In response to being asked for a clear method to assist amplification of these coils for experiment on cars.]

## Forward

After one learns, a method to record frequency, as it is felt, or generated. Then math can be used to increase effects in various ways. Once nodal distances are measured, a new world opens.
In my working days with Kosol, we were encouraged to drop the math, put down the measuring tools and first get the "feel" for the conscious energy personally. We were directed to study the platonic forms, build them, pulse them, and feel them.

Water - Icosahedron form platonic vibration - Moe Joe Cell
Quartz Crystal - Hex form platonic or tubular field. Center tube of a Joe Cell.
Copper - Tetrahedron or Star Tetrahedron - Twist or spin fields [Torsion Manipulation from Proton layer]
Iron - Twist or spin fields [Torsion manipulation from the electron layer]

Any material in a spherical layout, can generate a vibrational surface including a Christmas ornament. Cut a wire or rod the correct length [Copper or Iron], and use it to vibrate up the sphere, while the sphere vibrates it up, as they touch.
What is the correct length? Go back and study the platonic forms, get the formula for finding the outside segment length between two points from the diameter, which is the only information you will need.
A sphere can be vibrated up in any of the 5 platonic form structures using the correct wire length.

## Engine Considerations

Placing one low frequency at random from a device, on the engine shaft, from the carb, or air cleaner, or oil dipstick, and one random high frequency on the engine shell or car body, we have located sweet spots in the engine RPM ranges. This is a frustration because with two random frequencies interacting, the engine RPM becomes the tunner of the effect.

The solution, is of corse to place the correct two frequencies on engine shaft and crank case, to cause an acceleration at all RPMs, due to a constant cancellation of vibration, or smoothing out of the engines resistance to moton of mass.
The function or ratios of these vibrations need further exploration. We have had minimul success with the harmony frequency of pi/2.
The basic concept is to introduce the correct frequency into the oil, and water, to cause the power acceleration at all engine RPMs.

### Voltages with wire lengths

Where two long vibration resonant wires of different length generate a voltage, the longer wire will carry the negative charge.

## Working With Spheres

To work with spheres, one must have the mental model of the frequency form, and also the formula to find the resonance frequency, from the diameter of the sphere at the center of it's thickness.
Here is an example of the Icosahedron form as well as the formula necessary.

The only important design formula you need is Side = .5257391 x Diameter.
Fill a sphere with water, cut off a wire the correct length for that sphere, touch it to the sphere, and the Icosahedron vibration should rise from the sphere powered by the ratio of the sphere to the wire. Water should love this frequency form.

## Why is This Important

Say we want to create a coil that vibrates up water.
What is copper made of? Millions and millions of small spherical atoms, each one vibrating itself up already. This is where it's energy is located. Everthing we use it for, will at one level be vibrating on a sphere, no matter how we shape it or what other frequencies we run over the copper.

As the frequencies we use go higher and higher, the vibration will approach this atomic level, and the fields will not reach as far out in space, but become far stronger.

## Wire Coils

The simpelist way to couple a wire coil to an engine component such as the water or the Antifreeze, is to cut its length resonant with the liquids internal vibration.
GL frequency is just under 2" and happens to be a good water coupling frequency.
If you wrap a coil with a  ~2" diameter, each turn will be 2pi".
Each turn will now add mass, however frequency will jump and drop as you wind it. Where you cut the wire off, will shift the frequency drastically either upwards or downwards.

If the coil has 12 turns on it, the frequency of vibration will drop by 12x, and the mass in motion will multiply by 12x. The power will not change. This is because 12 is an even number divisible by both 3 and 4.

If you cut the coil off at 7 turns or 7x, the frequency will not drop at all. This is a prime number, and also an odd number. This coil will go outflow on one end and inflow on the other end and polarize itself end to end, like a Joe Cell tube is supposed to do.
The frequency on all 7 turns will be 1x, with 7 times the mass in vibration and 7 times the power.

I am describbing how to create a 2D resonance field on a coil, by setting the correct diameter, to cause the circumference to resonate with water. Then to increase it's field strength and polarity using count, or segment length count.

### 1D versus 2D resonance

Dealing with custom diameters is not easy.
One can ignor the diameter, and merely wind the coil length on any form, but having the diameter also correct will make a purely female coil.

As you wrap a resonant wire length on a random size coil form the circumference will be some function different then the wires resonant points and there will be a mixing to raise the pressure of the second dimension, although the length will still be exactly correct. A perfect wrap with circumference =  1x wire segment length, will generate a strong female energy. Missalignment will push this into a male energy with localized pressures from the coil.

Things to remember with coils,

An odd or prime segment numbered coil, will be different on each end as to male female energy.
An even numbered count will drop frequency, and may not be polarized end to end.

A CW will pull down higher frequencies, lowering it's torsion. And a CCW will pull up lower frequencies increasing the torsion.